MyTires4Less

Brake Pads, Rotors, Calipers & Brake Kits

Premium tires from 50+ brands — every size, every season

This category covers brake pads, rotors, calipers, brake kits and related hardware for cars, trucks and SUVs. The most important choice is pad compound, because it drives stopping feel, noise, dust and heat tolerance, so match it to how you drive, especially if you tow or haul.

Shop by Type

Brake Pad Compounds Compared

Pad compound is the friction material bonded to the backing plate. Each type trades off noise, dust and heat handling.

CompoundNoiseBrake dustHeat toleranceRotor wearTypical best use
CeramicQuietestLow, light coloredGood for daily drivingGentleCommuting and daily drivers
Semi-metallicCan be noisierHigher, darkerHighHigherTowing, hauling, trucks and spirited driving
Organic (NAO)QuietModerateLowestGentleLight vehicles and easy driving

Many trucks and heavy SUVs come from the factory with semi-metallic pads for their heat capacity, though ceramic pads formulated for trucks also exist. Some pad lines also offer severe-duty or fleet versions intended for repeated heavy stops. Inspect pads at every tire rotation. Read brake pads and rotors for help choosing.

Rotors: Smooth, Slotted and Drilled

  • Smooth (blank) rotors match most factory designs, run quietly and typically wear pads evenly.
  • Slotted rotors help clear gas and debris from the pad face, which can help under heavy use such as towing.
  • Drilled rotors aid cooling and wet performance on street cars, but lower-quality drilled rotors can crack around the holes under repeated hard use.
  • Drilled and slotted rotors combine both, mostly for appearance and street performance.

Every rotor has a minimum thickness stamped on it. A rotor worn or machined below that number should be replaced. Coated rotors resist rust on the hat and edges, which keeps them looking clean behind open-spoke wheels. A pulsing pedal, often blamed on warped rotors, is usually caused by uneven pad deposits or thickness variation, which correct bedding helps prevent.

Calipers, Kits and Hardware

A sticking caliper can cause pulling, uneven pad wear and a hot wheel. Remanufactured loaded calipers come with pads and hardware already installed, which can simplify the job. Brake kits bundle pads and rotors, and sometimes calipers, into a matched set for one axle. Replace clips, pins and boots when they are worn, and lubricate slide pins with a brake-specific grease.

Big brake kits with larger rotors and multi-piston calipers add heat capacity for performance driving or heavier loads, but they often require larger wheels for clearance, so check the minimum wheel diameter before ordering. Rubber brake hoses on older vehicles can swell or crack with age, and stainless braided lines can firm up pedal feel.

Brake Fluid, Bedding and Towing

Brake fluid absorbs moisture over time, which lowers its boiling point. DOT 3, DOT 4 and DOT 5.1 are glycol based and compatible with each other, though it is best to use the type your vehicle specifies. DOT 5 is silicone based and should not be mixed with them. After installing new pads or rotors, follow the pad maker's bedding procedure to lay down an even layer of pad material, which reduces noise and vibration. If you tow, choose pads and rotors with that load in mind, and make sure the trailer side is covered with a proper controller, as explained in trailer wiring and brake controllers. Our trailer hitch classes guide helps confirm your setup is within its ratings.

Brake Parts FAQs

How do I know when brake pads need replacing?

Replace pads when the friction material is worn to about 3 millimeters, or sooner if your vehicle maker specifies. Warning signs include a high-pitched squeal from the wear indicator, grinding, longer stopping distances or a dashboard brake wear light. Grinding often means metal is contacting the rotor, so inspect right away.

Should I replace rotors when I replace pads?

Often, but not always. Rotors that are above minimum thickness and are not warped, deeply scored or heat-cracked can be reused or resurfaced. Many shops replace them with the pads because modern rotors are thinner and often cost about as much as machining labor. Always replace pads and rotors in axle sets, both sides together.

Are ceramic brake pads good for towing?

Ceramic pads can work for light towing, but semi-metallic pads are typically the better choice for frequent or heavy towing because they tolerate more heat. Some brands offer ceramic pads formulated specifically for trucks and towing. Check the pad maker's intended use and follow your vehicle maker's recommendations.

Why do my new brakes squeak?

New brakes often squeak because the pads are not fully bedded, hardware is missing or dry, or the pad compound naturally makes some noise. Following the bedding procedure, using shims or anti-squeal compound on the backing plates and lubricating slide pins usually helps. Semi-metallic pads can be noisier by nature.

What is the difference between slotted and drilled rotors?

Slotted rotors have grooves that sweep gas, water and debris from the pad face, which suits heavy use like towing. Drilled rotors have holes that help cooling and wet braking but can be more prone to cracking under repeated hard stops. For most daily drivers, smooth rotors work well.

How often should brake fluid be changed?

Many vehicle makers recommend changing brake fluid every two to three years, though intervals vary, so follow your owner's manual. Brake fluid absorbs moisture, which lowers its boiling point and can cause a soft pedal under heavy braking. Towing, mountain driving and humid climates are good reasons to stay on schedule.

Buying guides

Sizing, fitment and what to look for, with in-stock picks.

Brakes buying guide
Brake Pads and Rotors: How to Choose the Right Parts
Pad compounds explained, when rotors need replacing, which upgrades are worth it for towing and performance, and how to get the most life out of a brake job.