MyTires4Less

LED Light Bars, Headlights & Off-Road Lights

Premium tires from 50+ brands — every size, every season

This category covers LED light bars, headlights, fog lights, work lights and trailer lights for trucks, Jeeps and trailers. The most important thing to know is where each light is legal: road lighting should carry DOT or SAE markings, while most light bars and auxiliary off-road lights are meant for off-road use only.

Shop by Type

LED vs Halogen vs HID Headlights

The three main headlight technologies differ in output, lifespan and how they behave in a given housing.

FeatureHalogenHID (xenon)LED
Typical output per low-beam bulbAround 1,000 to 1,500 lumensAround 2,500 to 3,500 lumensVaries widely; quality bulbs often 2,000 lumens and up
Typical service lifeAbout 500 to 1,000 hoursAbout 2,000 to 3,000 hoursOften 20,000 hours or more for the LED chips
Warm-up timeInstantA few seconds to full brightnessInstant
Typical color temperatureWarm, around 3,000 to 3,500 KAround 4,000 to 6,000 KCommonly 5,000 to 6,500 K
Power and heatHighest power draw for its outputNeeds a ballastLow power draw; needs heat sinking at the base

Ratings are typical and vary by product. Dropping an LED or HID bulb into a housing designed for halogen can scatter light and create glare for other drivers. A complete headlight assembly built for LED or HID usually controls the beam pattern better than a bulb swap.

LED Light Bars and Beam Patterns

Light bars and pods are sold by beam pattern, and many off-road setups combine more than one.

  • Spot beams throw a narrow, long-reaching beam for seeing far down a trail.
  • Flood beams spread wide for close-range and work light use.
  • Combo bars mix spot and flood optics in one housing.
  • Driving beams sit between the two, often with an elliptical pattern.

Check the IP rating for water and dust resistance; IP67 and IP68 are common for off-road lights. Raw lumen numbers can be hard to compare across brands, so beam pattern and optics matter as much as output. Amber or selective yellow lenses are popular for fog and dust because they can reduce glare off airborne particles. Work lights and rock lights are usually low-mounted floods for lighting the ground around the vehicle. Wire light bars through a relay, fuse and switch. Our LED light bar guide covers sizing and mounting.

Trailer Lights

Trailer lighting includes tail, stop and turn lamps, side markers, clearance lights and license plate lights. Federal rules call for additional clearance and identification lamps on trailers 80 inches wide or more. LED trailer lights are popular because they draw less power and are sealed against water, which helps on boat trailers that get dunked at the ramp. If lights flicker or fail, the cause is often a poor ground. See trailer wiring and brake controllers for connector types, and trailer tires and wheels for the rest of your trailer checklist.

Staying Street Legal

Most states limit how many auxiliary driving lights you can run on public roads, and many require off-road lights to be covered or switched off on the street. Look for DOT or SAE markings on headlights, fog lights and tail lights intended for road use. Rules vary by state, so check local regulations before mounting a light bar on the roof or bumper.

Aim headlights after installing new assemblies or lifting the vehicle, since a raised truck points the beam higher and can glare oncoming drivers. Many housings have marked adjusters, and the owner's manual usually explains the procedure. See lift and leveling kits if you are raising the truck.

Vehicle Lighting FAQs

Are LED light bars street legal?

In most states, LED light bars are not legal to use on public roads while driving. They are generally sold for off-road use, and many states require them to be covered or switched off on the street. Some smaller auxiliary lights carry SAE or DOT markings for fog or driving use. Check your state's rules before installing one.

Can I put LED bulbs in my halogen headlights?

Many LED bulbs physically fit halogen housings, but results depend on the housing. Reflector housings designed around a halogen filament may scatter LED light and cause glare. Bulbs that mimic the filament position tend to work better, and a full LED-designed headlight assembly typically gives the cleanest beam pattern. Check local rules on conversions.

What does IP67 mean on a light?

IP67 means the light is dust tight and can handle temporary immersion in water up to about 1 meter for around 30 minutes under test conditions. IP68 indicates protection beyond that, with the exact depth and time set by the manufacturer. Higher ratings suit lights mounted low on a vehicle or used on boat trailers.

Spot, flood or combo beam: which should I choose?

Choose a combo beam if you want one light that handles most jobs, since it lights both distance and the area around the vehicle. Pick spot for long-range trail or open desert driving, and flood for work areas, campsites and slow technical trails. Many people pair a spot bar with flood pods.

Why do my trailer lights not work properly?

The most common cause of trailer light problems is a bad ground connection. Corroded connector pins, broken wires and burned-out bulbs are next. Clean the plug contacts on both the vehicle and trailer, make sure the white ground wire is attached to clean bare metal, and test each circuit with a circuit tester.

Do I need a relay for an LED light bar?

Yes, for most light bars. A relay lets a small dash switch control the higher current the light draws, and an inline fuse protects the wiring. Many light bars are sold with a harness that includes the relay, fuse and switch. Very small, low-draw pods may not need one, but follow the light maker's instructions.

Buying guides

Sizing, fitment and what to look for, with in-stock picks.

Off-road lighting buying guide
LED Light Bars: How to Choose Size, Beam and Mount
Single row or double row, spot or flood, 20 inch or 50 inch curved: what the specs mean, where each size mounts, and how to wire it safely.
Body repair buying guide
Sherman Replacement Body Panels: Choosing the Right Panel for Rust and Collision Repair
Full assembly or patch panel, steel or aluminum, CAPA or standard: how restorers and body shops pick the right Sherman panel and get it to fit.
Boat trailer buying guide
Boat Trailer Parts: Bunks, Rollers, Guide-Ons and More
Worn carpet, cracked rollers or a boat that never loads straight: how to pick the right replacement parts and set the trailer up so launching is easy.
Off-grid power buying guide
Power Inverters, Generators & Solar Kits: How to Choose
How to size an inverter to what you actually plug in, when pure sine wave is worth it, and how inverter chargers, solar kits and generators fit together in a truck, RV or boat.
Roof rack buying guide
Roof Racks & Crossbars: How to Choose the Right System
Two bars or a full platform, bare roof or factory rails, weekend gear or a rooftop tent: how to pick a rack that fits your vehicle and your load.
ATV and UTV buying guide
ATV & UTV Accessories: What to Upgrade First
Tires, belts, axles and the gear that turns a quad or side-by-side into a work machine, plus the fitment traps that catch buyers.